Isometric illustration comparing artificial grass pile heights

When people ask about artificial grass thickness, they almost always mean pile height: the length of the blades, measured in millimetres from the backing to the tip. For most Irish gardens, a pile of 25mm to 35mm is the sweet spot. Go towards 20mm to 25mm where there is heavy daily traffic, and towards 35mm to 40mm for a soft, lawn-like look in a quiet garden. But pile height is only one number on the label, and a taller blade does not guarantee a better lawn. Density, face weight and the base underneath count just as much.

This guide explains what each figure means, matches thickness to real garden situations, and covers the other thickness question buyers meet: how deep the stone base under the grass needs to be.

Poweraggregates
Build a Better Base for Your Lawn
Power Aggregates supplies stone, sand and gravel for landscaping projects, with personalised advice for choosing materials for your garden base.

Ask about landscaping materials

TL;DR

Table of Contents

What artificial grass thickness actually means

There is no single “thickness” figure on a roll of turf. Suppliers use several measurements, and shoppers often mix them up.

Pile height is the length of the blades standing proud of the backing. It is the number in the product name: a 30mm grass has blades about 30mm long. Most listings give a tolerance too, often around plus or minus 10%, so a 40mm product can measure a little either side.

Face weight is the weight of the yarn alone, excluding the backing, usually in grams per square metre (g/m²). It rises when blades are longer, when there are more stitches per metre, or when the yarn itself is heavier.

Total weight adds the backing layers and coating to the yarn. This is why one 40mm grass may be listed at around 2,400g/m² and another at over 2,700g/m²: you are partly comparing backing as well as grass. Always check which of the two weights a listing quotes before comparing products.

Density is how many blades or stitches are packed into each square metre. It is the figure that decides whether the lawn looks full or you can see the backing between the blades.

Overall roll thickness, backing included, is a few millimetres more than the pile and rarely matters when you buy. What does matter in practice is how the pile, density and backing work together.

Pile heights you will find on sale in Ireland

Irish suppliers typically stock pile heights from around 10mm for play surfaces and balcony use up to about 40mm to 50mm for luxury lawns. The common garden options sit in between:

Pile height Look and feel Best suited to
10mm to 20mm Short, flat, tidy Balconies, roof terraces, very heavy foot traffic, tight budgets
25mm to 30mm Neat, natural, resilient Family gardens, dogs, football, trampolines, play areas
32mm to 38mm Fuller, softer, realistic Show lawns and front gardens with moderate use
40mm to 50mm Plush, deep, very lawn-like Quiet, low-traffic areas where appearance comes first

These are rules of thumb. A good 25mm grass with dense, well-shaped yarn can look better than a poor 38mm one.

How thickness changes the look, feel and wear

Pile height is a trade-off between softness and resilience.

Shorter pile (about 20mm to 30mm) stands up better to repeated footfall. Short blades have less leverage working against them, so they are less inclined to lie down and mat. The surface feels firmer and looks like a closely mown lawn.

Longer pile (about 35mm to 50mm) is softer underfoot and looks lusher from the kitchen window. The downside is that long, unsupported fibres can bend under their own weight and look tired, especially if the yarn is thin or the density is low. Brushing helps, but it cannot rescue a sparse product.

Think of it like a real lawn. A tight, short sward takes a football match. A deep, soft one is lovely to lie on but shows every path you walk across it.

How thickness changes the look, feel and wear — overview diagram

Why taller is not automatically better

Price often climbs with pile height, because longer blades use more yarn. That makes it tempting to assume the longer grass is the premium product. It is not always so. A tall pile with a low stitch count lies flat, shows the backing and wears quickly. A mid-height pile with high density stands up, hides the backing and holds its shape for years.

In our experience of supplying landscaping materials across Ireland, the gardens that disappoint are rarely those with a 25mm pile. They are the ones where the buyer chose by height alone, then laid it on a poorly prepared base.

Power Aggregates, Carrigtwohill Industrial Estate, Municipal District of Cobh
Poweraggregates
Explore Materials for Your Garden
Visit Power Aggregates to discuss landscaping materials with a team experienced in supplying stone, sand and gravel for projects of all sizes.
Power Aggregates
Carrigtwohill Industrial Estate, Municipal District of Cobh

Get directions

Which thickness suits which situation

A family garden with children

Choose 25mm to 30mm. It recovers well after football, a trampoline base or garden furniture has been sitting on it, and it feels comfortable to play on. If children will use it every day, lean to the shorter end. Look for resilient yarn shapes sold as having good bounce-back.

Dogs and pets

Short to medium pile, around 25mm to 30mm, is easier to keep clean. Urine and mess rinse through more easily when the blades are not so long that they trap debris. Whatever pile you choose, the surface needs to drain freely, which brings us back to the base. Our guide on how artificial grass creates a low-maintenance garden covers day-to-day upkeep.

High-traffic paths, side passages and balconies

Go for 15mm to 20mm. A short, flat surface resists flattening where people walk the same line every day. It also suits terraces and balconies where you do not want a deep, shaggy look.

A front or show lawn

Pick 32mm to 40mm if the area is mostly looked at rather than walked on. This is where a fuller, softer pile pays off visually. Check density closely, because this is where sparse tall grass shows its weakness first.

Dense artificial grass on an Irish front lawn

A mixed garden

A 30mm grass is the safest all-rounder. It is long enough to look natural and short enough to cope with the occasional kickabout. If you are unsure, order a sample and test it in your own light, since colour and sheen change dramatically outdoors, and walk on it.

The specifications to compare alongside pile height

Before choosing a thickness, read the whole specification. These are the lines that tell you whether a grass will last:

  1. Pile height. The blade length in mm, with its tolerance.
  2. Density or stitch rate. Higher density gives a fuller look and better recovery. Premium grass is often described as starting somewhere around 25,000 to 29,000 blades per square metre, though makers measure differently, so compare like with like.
  3. Face weight and total weight. Make sure you know which one is quoted.
  4. Yarn type and shape. Curled, C-shaped or W-shaped fibres hold the pile upright better than flat, straight yarn. A mix of colours, such as lime and olive tones, looks more natural than a single flat green.
  5. Backing and coating. The backing locks the fibres in and lets water through. Check that it is perforated for drainage.
  6. UV stabilisation. Important for colour retention, even with Irish skies.
  7. Roll width and length. Rolls commonly come in 2m or 4m widths and are cut to length, so plan your layout to avoid unnecessary seams.
  8. Warranty. A longer warranty from the maker is a good sign of confidence in the product.

Measuring so you buy the right amount

Measure the width and length of the area in metres and multiply to get square metres. Then allow extra length for trimming and fitting, and plan for adjoining rolls to overlap slightly before you cut them to a clean edge. For awkward shapes, sketch the garden and divide it into rectangles. Ordering a little extra costs far less than running short with a visible join in the middle of the lawn.

The other thickness: how deep should the base be?

Searchers often ask about the depth of the base, and the base matters more than most buyers expect. Artificial grass does not fix problems underneath it. If the ground moves, holds water or is uneven, you will see it in the lawn within a season.

A typical build for a domestic lawn in Ireland looks like this:

Layer Typical depth Purpose
Excavation About 100mm to 150mm below the final finished level Makes room for the base and keeps the grass flush with paths and edges
Compacted sub-base of clean crushed angular stone About 65mm to 100mm Provides strength and drainage
Levelling layer of fine stone or grit sand About 25mm Gives a smooth, even surface for the turf
Artificial grass 15mm to 50mm pile The visible surface

Specialists vary a little in their figures, with some excavating around 4 inches and others around 150mm, and some using a shock-pad underlay for play areas, which needs the base to finish slightly deeper. The principle stays the same: compact each layer thoroughly, keep the stone angular so it locks together, and make sure the finished base sits a little below the adjoining paving or edging so the grass finishes level with it.

Drainage comes first

The stone sub-base is what lets rain pass straight through. On heavy clay or low-lying Irish ground, you may need to improve the drainage before you lay anything. Understanding landscaping and property waterproofing helps you think about falls, run-off and keeping water away from the house when you plan a new lawn area.

If you are covering an existing gravel area rather than digging out, see our step-by-step guide to laying artificial grass on gravel, and our overview of getting the base and drainage right.

Base materials: what to order

The sub-base is usually a clean, graded crushed stone, and the levelling layer is a finer stone dust or grit sand. Quantities depend on area and depth, so calculate square metres multiplied by depth in metres to get cubic metres, then convert to tonnes with your supplier’s guide to how much a cubic metre weighs. Add a small allowance for compaction. For drainage-related stone, our page on drainage stone explains sizes and uses.

Perspective: why we tell customers to look beyond the number

We supply stone, sand and gravel from our own quarries, and every artificial grass project we hear about comes back to the same point: the ground matters more than the label. Customers phone asking for the thickest grass because they assume it is the best. Our advice is to decide how the area will be used, pick a pile height to suit, then spend your effort and budget on a properly compacted, free-draining base. A 30mm grass on a good base will look better in five years than a 40mm grass on soft, uneven ground.

We also encourage people to ask for a sample, ask what density they are buying, and tell us the size of the area so we can advise on the quantity of base material rather than guess. That is how we help small gardens and large commercial jobs alike.

— Constantin

Buying the base materials from us

If you are planning a lawn, we supply the crushed stone, sand and drainage stone that go underneath, along with artificial grass, with nationwide delivery and advice from a team that knows the materials. Tell us the area and the finished depth you want, and we will help you work out what to order.

Poweraggregates

Browse the full range in our online shop, or look at our sand and drainage categories for the base layers.

Common thickness mistakes to avoid

FAQ

What is the best thickness for artificial grass?

For most Irish gardens, a pile height of 25mm to 35mm gives the best balance of natural look and durability. Go shorter, around 20mm to 25mm, for heavy traffic and play areas, and longer, around 35mm to 40mm, for quiet front lawns.

Is 40mm artificial grass better than 30mm?

Not necessarily. The 40mm grass feels softer and looks more lush, but it can flatten sooner if the density is low or the area is heavily used. A dense 30mm product is often the more durable choice for family gardens.

What is the difference between pile height and face weight?

Pile height is how long the blades are, in millimetres. Face weight is how much yarn is packed into each square metre, excluding the backing. Together with density, these tell you how full and hard-wearing a lawn will be.

How deep should the base be for artificial grass?

Allow about 100mm to 150mm of excavation below your finished level, filled with compacted crushed angular stone and topped with roughly 25mm of fine stone or grit sand. Ground conditions and use, such as a play area with shock pad, can change the figures, so ask your installer or supplier for advice on your site.

Does artificial grass pile height affect how it drains?

Pile height has little effect on drainage. Drainage depends on the perforated backing and, above all, the free-draining stone base below, so get the base right whichever pile you choose.

Sources

This guide draws on our own published installation and materials guides:

Poweraggregates
Discuss Your Artificial Grass Base
Contact Power Aggregates for personalised advice on stone, sand and gravel options for your landscaping project, from a garden renovation to a larger job.
Call Now Button