Use clean, washed, open-graded drainage stone in the 10–20mm range (a #57 equivalent), never pea gravel or anything with fines. Get those two things right, the stone and the fabric envelope, and the drain works for decades rather than years.
TL;DR:
- Using washed, angular gravel in the 10–20mm range is essential for a French drain to last decades and avoid clogging within five years.
- A trench width of about one foot and an 18 to 24 inch depth suits a four-inch pipe, with a slope of at least 1 percent to ensure proper water flow.
- Proper installation sequence includes lining with geotextile fabric, adding a bedding layer of washed stone, and ensuring the pipe’s holes face downward for efficient drainage.
- Ordering at least 10 percent more gravel than calculated helps prevent shortages, especially on longer runs or in difficult soil conditions.
- Common mistakes include using unwashed stone with fines, laying pipe directly on soil, and neglecting slope, all of which significantly reduce drain lifespan.
Table of Contents
- Best gravel for a French drain: sizes and why washed stone matters
- How wide and deep should the trench be?
- Step-by-step French drain installation you can follow on-site
- How much gravel do you need for your French drain?
- Common French drain mistakes and how to spot trouble early
- What our supplier experience tells us about checking stone on delivery
- Why the “any old gravel will do” advice keeps failing homeowners
- Ordering the right stone for your French drain
- Sources
- FAQ
Best gravel for a French drain: sizes and why washed stone matters
The stone itself decides whether your French drain lasts 20 years or clogs in five. The standard is clean, washed, angular drainage stone, commonly sold as 10–20mm or 20mm gravel, and matching the American #57 (¾ inch) specification that most installation guides reference. A finer alternative, closer to #67, works in tighter trenches where you need the stone to pack a bit closer around a smaller pipe, but washed quality matters more than the exact size you pick.
“Washed” means the quarry has rinsed out the sand, clay and dust left behind from crushing. Skip that step and those fines migrate downward, packing into the gaps between stones and around the pipe perforations. That’s the single fastest way to turn a working drain into a boggy trench.
Avoid these for a structural French drain:
- Crusher run or any “as dug” aggregate still carrying dust and fines
- Pea gravel, which is smooth and rounded rather than angular, so it settles and compacts over time
- Any stone you can’t get a clear answer about when you ask “is this washed?”
A quick buyer check costs nothing: grab a handful from the pallet or bag and rub it between your palms. Washed stone leaves your hands mostly clean. Unwashed stone leaves a fine grey film. If you’re ordering by phone or online, simply ask the supplier for washed drainage stone with no fines, and confirm the nominal size before it ships. Bagged stone suits small runs and tight access; bulk delivery is cheaper per tonne for anything over a few metres.
Pro Tip: Keep a golf-ball-sized sample from your delivery in a jar of water for 30 seconds. If the water clouds noticeably, the load has more fines than it should, and that’s worth raising with the supplier before you backfill.

Our 10–20mm drainage stone guide covers sizing for wall and foundation drainage specifically, if your project sits close to a structure.
How wide and deep should the trench be?
For a standard 4 inch perforated pipe, dig the trench about a foot wide and roughly 18 to 24 inches deep. That gives enough room for a bedding layer, the pipe itself, and a proper stone envelope without wasting excavation effort on a trench wider than the job needs. Larger pipe, 6 inches or more, needs a wider trench, typically 15 to 18 inches, to keep adequate stone coverage on both sides.
Slope is the part DIYers get wrong most often. Building regulation guidance sets a minimum fall of roughly 1%, which works out to about 1 inch of drop for every 10 feet of run. That’s the floor, not the target.
- Minimum acceptable slope: 1% (1 inch per 10 feet)
- Preferred slope for self-cleansing flow: 1–2%
- Clay-heavy or poorly draining ground: lean toward 2%, since horizontal percolation through clay is weak and the pipe ends up carrying most of the water
A trench that falls short of 1% slope over its length lets water pool instead of flow, and pooled water is exactly what lets silt settle out of suspension inside your pipe.
Before you dig, confirm three things: where the water will actually discharge, whether any utilities cross your route, and whether your local authority has rules on where you’re allowed to send that discharge. Skipping that last check is how DIY drains end up sending water onto a neighbour’s land.
Step-by-step French drain installation you can follow on-site
Getting the sequence right matters as much as getting the materials right. Here’s the order that avoids rework:
- Mark the route and set your grade. Run a string line from the highest point to the outlet, using a level to confirm you’re holding at least 1% fall throughout.
- Call before you dig. Confirm there’s nothing buried along the route, then dig the trench to your target width and depth, checking the slope every few feet with a spirit level laid across a straight board.
- Line the trench with geotextile fabric, letting enough overhang each side to fold back over the top later. This “burrito wrap” method, lining fully rather than relying on a sock-wrapped pipe alone, holds up far better in silty or clay soils where fine particles are constantly trying to migrate into the stone.
- Lay the perforated pipe with holes facing down. Groundwater rises from the trench bottom rather than dripping in from above, so downward-facing holes collect it more efficiently. Join lengths with couplings, keeping joints tight.
- Backfill with stone to at least 4 to 6 inches above the pipe crown.
- Fold the geotextile fabric back over the top of the stone, overlapping the edges so no soil can work its way down the sides.
- Backfill the remaining trench with the excavated soil or a topsoil layer, and finish the surface to match the surrounding ground.
An optional cleanout riser at the highest point, a short vertical pipe stub capped at grade, gives you somewhere to flush the line years down the track without digging it up.
Pro Tip: Renting a walk-behind trencher for runs over about 15 metres saves hours compared with hand-digging, and it holds a straighter, more consistent depth than most people manage freehand with a spade.
How much gravel do you need for your French drain?
The working formula is straightforward: length × width × depth, divided by 27, gives you cubic yards (or convert your measurements to metres for cubic metres). For a typical 12 inch by 18 inch trench, the practical rule of thumb is about 1.4 cubic feet of stone per linear foot, once you’ve allowed for the pipe itself displacing some volume.
A worked example: a 20 foot run at 12 inches by 18 inches needs roughly 28 cubic feet of stone before waste, which is about 1.05 cubic yards. Add a 10% waste allowance and you’re ordering closer to 1.15 cubic yards, or around 31 cubic feet.
| Trench run | Stone needed (before waste) | With 10% waste allowance |
|---|---|---|
| 10 ft (12in × 18in) | 1.4 cubic feet | 1.4 cubic feet |
| 20 ft (12in × 18in) | ~28 cubic ft | ~31 cubic ft |
| 20 ft (12in × 18in) | 28 cubic feet | 28 cubic feet |
For anything under a few cubic feet, bagged stone from a shop is simplest. Beyond that, bulk delivery works out far cheaper per unit and saves you hauling dozens of bags across the garden. Order that extra 10%, or round up to the next small pallet. Running short halfway down a trench on a Saturday afternoon is a genuinely miserable way to lose a weekend.
Common French drain mistakes and how to spot trouble early
Most French drain failures trace back to the same handful of errors:
- Using stone with fines, or crusher run instead of washed stone — fines migrate and clog the voids around the pipe within a few seasons rather than decades.
- Skipping the geotextile fabric — without it, surrounding soil works its way into the stone from every direction, not just from above.
- Laying pipe directly on soil or fabric with no bedding — perforations press against the ground and silt in almost immediately.
- Building the trench below 1% slope — water pools instead of moving, and standing water lets sediment settle inside the pipe.
- Discharging into a spot with nowhere for the water to go — a dry well that’s too small or an outlet that floods sends water straight back up the trench.
Each of these causes gradual siltation rather than sudden failure, which is exactly why they’re easy to miss until the drain stops coping with heavy rain.
Once installed, check outlets after storms for flow, and clear debris from any visible inlet grates a couple of times a year. If water is backing up and you’ve got a cleanout riser, flush it with a hose. Persistent standing water, a sudden drop in flow, or a smell from the outlet are signs worth a camera inspection rather than more digging. A drain less than five years old that’s already failing usually points to a materials or slope problem at installation, and that’s a repair job, not a patch job.

Pro Tip: Mark your outlet location with a small painted stone or stake before winter. It’s astonishing how quickly grass grows over the exact spot you need to find again in March.
What our supplier experience tells us about checking stone on delivery
Constantin, writing for Power Aggregates, has spent years fielding calls from gardeners and contractors trying to work out why a drain that looked fine on day one had failed within two years. Almost every one of those calls traces back to stone quality, not the digging.
A few checks take two minutes and save a rebuild:
- Look at the delivery load in daylight. Genuinely washed stone looks clean and slightly damp, not dusty or grey.
- Run the jar test described earlier: cloudy water after a light rinse means more fines than the load should carry.
- For larger jobs, ask your supplier for the gradation spec rather than trusting the bag label alone.
If you’re dealing with heavy clay ground, a complicated outlet, or a run longer than 20 metres, it’s worth a call to a supplier who actually knows the stone before you order, not after the trench is dug.
Why the “any old gravel will do” advice keeps failing homeowners
The most common piece of DIY advice, that any gravel will drain water, is technically true and practically useless. Water finds its way through almost any loose stone on day one. The question is whether it still does that in year six, and that’s entirely down to whether the stone was washed and whether fabric kept soil out of the voids.
Where most guides undersell the job is slope. People fixate on the pipe and the stone and treat a 1% fall as a nice-to-have rather than the number that decides whether the system self-cleans or slowly silts up. A trench dug flat, or worse, sloping the wrong way by an inch over its length, behaves nothing like the same system on paper.
If there’s one thing worth spending money on rather than cutting corners, it’s the stone itself. A cheaper unwashed load might save you a small amount on a typical domestic run, against a system that could need digging up within a handful of years instead of running for decades. Get the fabric wrap and the slope right too, and there’s genuinely little reason for a well-built French drain to fail before the house around it does.
— Constantin
Ordering the right stone for your French drain
Washed drainage stone is available in both bagged and bulk quantities, with nationwide delivery direct from quarries. When you order, ask specifically for washed drainage stone with no fines, in the 10–20mm range, or tell us your pipe size and trench dimensions and we’ll confirm the right spec for the job.

Whether you’re doing a single garden run or a larger job around a house foundation, our decorative stone range covers the sizes and grades this guide recommends, sourced and washed before it ever reaches a pallet. If your project also needs surface finishing once the drain is backfilled, our guide on keeping gravel from washing away is worth a read before you top off the trench. Get in touch for a quote with your trench length and pipe diameter to hand to determine exactly how much stone to order.
Sources
This guide draws on building regulation technical guidance, This Old House’s installation walkthrough, and technical notes on drainage slope hydraulics. Check with your local building authority before finalising discharge points.
- French drain calculator & guide — RemodelCalculators
- Best stone for a French drain — Komplet America
FAQ
Do you put gravel under a French drain?
Yes. A 2 to 3 inch bedding layer of washed stone under the pipe keeps it off bare soil or fabric, so perforations stay clear rather than pressing directly against the ground.
What size gravel should I use for a French drain?
Clean, washed stone in the 10–20mm range, equivalent to a #57 spec, is the standard choice; a finer #67 alternative works in tighter trenches, but washed quality matters more than the exact size.