A gravel driveway typically requires a compacted sub-base in a range commonly around 100 to 150 mm for normal car use, topped with a surface gravel layer that is often between 20 and 50 mm. For weak clay, soft ground, or frequent van and EV traffic, thicker sub-bases are generally recommended, often starting around 150 mm and increasing as needed. Get the sub-base right and the surface layer looks after itself for years.
TL;DR:
- The sub-base depth should be at least 100 mm for firm ground and can reach 200–300 mm for soft or weak soils, especially under heavy traffic or vans.
- Over-order loose material by 15–25% to account for compression during compaction, meaning a 150 mm compacted layer often needs about 170–190 mm of loose aggregate.
- When using finer gravel, 10 mm packs tighter but can migrate more in wet weather, while 20 mm gravel offers better lock-up and resistance to rutting.
- Repeated pooling or rutting indicates underlying sub-base failure, requiring excavation, proper compaction, and sometimes a geotextile layer for repair.
- Prioritize deep, well-compacted sub-base construction over surface gravel thickness to ensure long-term driveway stability and avoid costly rebuilds.
Table of Contents
- Recommended gravel driveway depths at a glance
- How to decide the right depth for your site
- Building the driveway layer by layer
- Getting the installation right
- Common mistakes and how to fix them
- Practical tips from Power Aggregates
- Why the base matters more than the surface
- Ordering the right materials for your driveway
- Sources
- FAQ
Recommended gravel driveway depths at a glance
Depth requirements change with soil, traffic, and how much settling you can tolerate. Government guidance on driveway construction sets 100–150 mm of compacted sub-base as the baseline for a normal family car, rising to 150–250 mm on heavy traffic or weak clay soils.
| Use case | Compacted sub-base | Surface gravel | Total depth |
|---|---|---|---|
| Light car, firm ground | 100 mm | 20–30 mm | 100–150 mm |
| Standard family use | 100–150 mm | 30–40 mm | 170–190 mm |
| Regular vans / heavy vehicles | 150–250 mm | 40–50 mm | 190–300 mm |
| Soft subgrade or made ground | 200–300 mm+ | 40–50 mm | 200–300 mm |
Order more loose material than the compacted figures suggest. Aggregate compresses once it’s spread and rolled, and engineering guidance on compaction and bulking puts that bulking factor at 15–25%. A 150 mm compacted layer typically needs 170–190 mm of loose material before you start rolling it flat.
A few things to weigh when choosing surface grit:
- Finer 10 mm gravel packs tighter and feels firmer underfoot but can migrate more in wet weather.
- Coarser 20 mm gravel locks together better under vehicle weight and resists rutting.
- Rounded pea gravel looks attractive but tends to roll and needs deeper, sturdier edging to stay put.
How to decide the right depth for your site
The 100–150 mm figure works as a starting point, not a fixed rule. Engineering guidance on driveway sub-base thickness makes the point plainly: there is no single standard depth, because thickness has to scale with axle load and soil strength together.
Soil type moves the number first:
- Free-draining gravel or sand subgrade: stick to the lower end, around 100 mm.
- Firm clay: add 50 mm or more, since clay holds water and softens under repeated loading.
- Soft made ground or fill: go to 200–300 mm, and consider a geotextile separation layer underneath.
Axle load matters more than most people assume. A compact car and a small van look similar in size, but the van’s wheel loading is often far higher, concentrated on fewer contact points. Plan your depth around the heaviest vehicle that will use the drive regularly, not the one you drive most often. An EV, loaded with battery weight, can behave more like a van than a hatchback on paper specs.
Drainage and frost cycles also push depth up. Standing water softens the sub-base from below, and repeated freeze-thaw movement loosens compaction over a season or two. Poor natural drainage is one of the clearest signals for laying a geotextile membrane beneath the sub-base to stop it mixing with the soil underneath.

Pro Tip: If your drive is long, slopes noticeably, or will see daily van or lorry traffic, get an engineered design rather than relying on rule-of-thumb depths. A short domestic drive on decent ground rarely needs it, but a commercial access route almost always does.
Building the driveway layer by layer
Every well-built gravel driveway is really three separate jobs stacked on top of each other, and each one has its own job to do.
The sub-base carries the structural load. Use a certified Type 1 or MOT-style crushed stone, compacted to 100–150 mm for cars and light traffic, rising to 150–250 mm on clay or for heavier use. A suitable hardcore for a driveway sub-base needs sharp, angular particles that lock together under compaction, not rounded stone that keeps shifting.

An optional binder layer sits between sub-base and surface on some builds, particularly where the finished surface will take heavier or more frequent loading. Where used, it typically adds 50–80 mm of finer crushed stone, giving a smoother transition before the decorative top layer goes down.
The wearing course is what you see and walk on. Recommended sizes run from 10 mm to 20 mm stone, laid at 20–50 mm compacted depth depending on how coarse the gravel is and how much lock-up you want underfoot.
Two extras protect the whole structure:
- A geotextile membrane between subgrade and sub-base stops soft ground migrating upward and contaminating the stone above it.
- Edge restraints in concrete, metal, or timber stop the sides spreading and keep gravel from creeping onto lawns and paths; a well-detailed gravel driveway edging job does more to control long-term maintenance than almost anything else in the build.
Getting the installation right
The finished depth only matches your design if the process behind it is sound. Follow these steps in order:
- Excavate to the target depth plus allowance. Dig out enough for the full compacted sub-base and surface layer, plus a small margin for bedding and edge restraint thickness. Check levels with a straight edge and spirit level before you order a single tonne of stone.
- Compact in lifts of 75–100 mm. Spread the sub-base in stages and run a plate compactor over each layer before adding the next; practical compaction guidance is consistent on this point across residential and commercial jobs. Compacting one thick loose layer in a single pass leaves the bottom uncompressed, and it settles unevenly within months.
- Order for bulking, not for the finished figure. Apply the 15–25% bulking factor to your compacted target. A driveway needing 150 mm compacted over 40 square metres (6 cubic metres finished) typically needs around 7 to 7.5 cubic metres of loose material delivered.
- Set crossfall and drainage before laying gravel. A gentle slope of around 1 in 40 to 60 sheds surface water toward a soakaway or drain rather than pooling on the sub-base.
- Fit edge restraints and any gravel grids last. Compacting a sub-base properly before restraints go in means the edging sits against a stable shoulder rather than loose fill.
Common mistakes and how to fix them
Most failed gravel driveways trace back to one root cause: the sub-base was never deep enough or compacted well enough to begin with.
Watch for these warning signs:
- Ruts or wheel tracks forming within the first year, especially near the entrance.
- Gravel disappearing into the soil below, leaving a muddy top layer that never firms up.
- Standing water after rain that takes hours to drain away.
A thin top-up of fresh gravel fixes cosmetic thinning from normal wear, and most drives need a 25 to 50 mm top-dressing every two to three years regardless of how well they were built. Rutting and pooling are different problems entirely: they mean the sub-base itself has failed, and no amount of extra surface stone will solve it. That calls for excavating back down, adding a geotextile membrane if there wasn’t one, and rebuilding to the correct compacted depth.
Edge restraints and drainage stone corridors solve migration issues without a full rebuild in most cases, and driveway installation guidance backs strong edging as one of the most effective, lowest-cost fixes available. Spending a little more on sub-base depth at the outset is almost always cheaper than a repeat rebuild two years later.
Practical tips from Power Aggregates
Ordering the right depth means ordering the right products. Power Aggregates supplies:
- Crushed stone and Type 1 hardcore for sub-base layers, in sizes suited to compaction.
- 10 mm and 20 mm decorative gravels for wearing courses, plus gravel path depth guidance for smaller areas.
- Drainage stone and geotextile-compatible aggregates for poor ground.
Before ordering, dig a test hole and check for soft, wet, or peaty ground; it changes the depth you need.
Why the base matters more than the surface
Homeowners spend most of their budget on the gravel they can see and treat the sub-base as an afterthought. That’s backwards. A driveway with a slightly thin surface layer still functions; a driveway with a slightly thin sub-base fails within a season or two. If you’re deciding where to put extra money, put it a few centimetres deeper into the ground, not a few millimetres thicker on top.
If you’re unsure what depth or quantities your project needs, get in touch with suppliers for a quote. Discussing soil type and vehicle use can help avoid costly rebuilds later.
— Constantin
Ordering the right materials for your driveway
Suppliers offer sub-base stone, decorative gravel, and drainage aggregates suitable for driveway projects, often sourced from quarries and available with delivery options. That means one order, one delivery slot, and one point of contact for both your 100–150 mm sub-base and your finished wearing course, rather than juggling separate merchants for hardcore and decorative stone.

Start by browsing decorative stone and gravel options to settle on a surface size, or read choosing the right gravel for driveways, paths, and gardens if you’re still deciding between 10 mm and 20 mm stone. Once you know your area and target depth, get in touch for a quote covering both sub-base and surface quantities, including the bulking allowance, so you order the right volume the first time.
Sources
- Government guidance on driveway construction (summary)
- How thick should a driveway sub-base be? (Garden Engineering)
- Driveway installation guide (ConcreteMaths)
These sources set the numeric floor for every depth figure in this guide.
FAQ
How deep should a 20 mm gravel driveway be?
Laying 20 mm gravel for the wearing course is commonly done at a compacted depth between about 30 and 50 mm, typically on top of a sub-base compacted to roughly 100 to 150 mm for normal car use.
How thick should a gravel driveway be overall?
Total compacted depth for standard family driveway use generally ranges approximately from just over 100 mm up to nearly 200 mm, combining a sub-base often between 100 and 150 mm with a surface layer usually up to 50 mm. For clay soils or heavier vehicle traffic like vans or EVs, deeper construction is typically recommended, often well above the typical family use depths.
Should I use 10 mm or 20 mm gravel for my driveway?
20 mm gravel locks together better under vehicle weight and resists rutting, while 10 mm gravel feels smoother underfoot but shifts more easily; either works if the sub-base beneath it is deep enough.
How deep should I dig for a gravel driveway?
Dig out the full compacted sub-base and surface depth plus a small allowance for bedding, typically 150–250 mm total for a standard drive and up to 300 mm or more on soft ground.
Does Power Aggregates supply materials for both the sub-base and surface layer?
Yes, Power Aggregates supplies crushed stone and Type 1 hardcore for sub-bases alongside decorative surface gravels, and can advise on quantities including bulking allowances for a specific project.