Gravel size numbers describe the nominal maximum particle size that passes through a specific sieve, and that single measurement determines whether a stone works for a driveway, a drain or a flower bed. As a rough guide, driveway top layers suit 8 to 20 millimetres, drainage stone works best at 10 to 20 millimetres, and decorative pea gravel sits around 3 to 8 millimetres. The chart and supplier checklist below will help you match a number on a bag to the job in front of you.
TL;DR:
- Gravel size labels, whether US numbers or ISO classes, are approximate; always verify the actual millimeter range listed by the supplier.
- A typical driveway build requires a 40 to 63-millimeter coarse sub-base, a 75 to 100-millimeter crusher run binder layer, and a 25 to 50-millimeter top layer of #8 gravel or pea gravel.
- Angular crushed stone interlocks better and is suitable for structural layers, while rounded gravel is more comfortable but less stable for load-bearing applications.
- Rounded pea gravel looks natural and is best for decorative borders and play areas, whereas angular gravel performs better in driveways and drainage runs.
- Proper layer depths and compaction are crucial; a driveway should have assingle layer depths of approximately 100-150 millimeters for the sub-base, 75-100 millimeters for the binder, and 25-50 millimeters for the surface.
Table of Contents
- How gravel sizing systems actually work
- A gravel size chart you can use when ordering
- How shape, fines and rock type change performance
- Which gravel size fits your project
- Getting the layers and depths right
- What to check before and after your gravel arrives
- Getting the balance between looks and durability right
- How Power Aggregates can help you get the right size
- Sources
- FAQ
How gravel sizing systems actually work
Every gravel size starts with a sieve test. A sample is shaken through a stack of mesh screens with progressively smaller holes, and the size at which most of the material stops falling through becomes its nominal maximum size. This concept, borrowed from concrete mix design, is explained in detail in an FHWA training module on aggregate grading, which notes that nominal maximum aggregate size is central to ACI mix design and that a load can be graded as well-graded, gap-graded or open-graded depending on how evenly the particle sizes are spread. A well-graded mix packs tightly with fewer voids, which matters for a sub-base layer, while an open-graded stone leaves gaps that water can move through, which matters for drainage.
Two labelling systems dominate the market, and they rarely line up neatly.
- US numbered sizes (such as #8, #57 or #3) come from state department of transportation gradation tables and refer to a specific sieve range rather than a single measurement.
- ISO 14688 metric classes split gravel into fine (2 to 6.3 millimetres), medium (6.3 to 20 millimetres), and coarse (20 to 63 millimetres), according to the classification summarised on Wikipedia’s gravel entry.
- Supplier product names (pea gravel, crusher run, chippings) describe the look or use of a stone rather than its sieve range, so two suppliers’ “20 mm gravel” can differ slightly in practice.
Because these three systems overlap rather than match exactly, the safest habit is to ask for the millimetre range printed on the product page or delivery note rather than relying on a name or number alone. A bag labelled #57 in one catalogue might sit anywhere from 9 to 25 millimetres, so the number is a starting point, not a guarantee.
A gravel size chart you can use when ordering
The table below groups the sizes most commonly sold for landscaping and construction, with a typical millimetre range and the job each one suits best. It draws on the metric classes in ISO 14688 and on standard industry gradation tables.
| Common name | Typical size range | Best for |
|---|---|---|
| Pea gravel | 3 to 8 mm | Decorative borders, pathways, play areas |
| #8 gravel | 9 millimetres | Driveway top layers, exposed aggregate concrete |
| #57 gravel | 9 to 25 mm | General drainage, driveway base, French drains |
| — | 9 to 25 mm (mixed) | Driveways, backfill, mixed drainage use |
| #3/#4 gravel | 40 to 63 mm | Driveway sub-base, large drainage voids, erosion control |
| Crusher run / DGA | 0 to 40 mm (graded mix) | Compacted binder layer under paving and driveways |
| Screenings | Under 5 mm (fine dust to grit) | Jointing sand alternative, fine levelling layer |
Reading a photograph of gravel tells you almost as much as the label does. Rounded, smooth particles (pea gravel, river gravel) come from water-worn deposits and tend to roll underfoot. Angular, sharp-edged particles (crushed limestone, crusher run) come from quarried rock that has been mechanically broken, and they lock together far more readily once compacted.
How shape, fines and rock type change performance
The same millimetre range can behave completely differently depending on what the stone is made of and how it was produced. Angular crushed stone, most often limestone or granite, interlocks under compaction because the broken faces grip against each other, and the FHWA module notes that this shape typically gives a stronger mechanical bond than rounded river gravel in structural applications. Rounded pea gravel and river gravel, by contrast, shift and roll rather than lock, which is exactly why they look and feel pleasant underfoot but make a poor choice for a load-bearing base.
Fines, the dust-sized particles mixed in with larger stone, play a double role. In a binder or sub-base layer, fines fill the gaps between larger stones and help the layer compact into a solid, stable mat. In a decorative top layer, those same fines clog drainage, trap moisture and turn to mud in wet weather, which is why washed, fines-free stone is the usual choice for anything you will walk or drive on regularly.
- Rounded stone suits decorative and low-traffic use where comfort and appearance matter more than load-bearing strength.
- Angular crushed stone suits structural layers, driveways and drainage runs where interlock and stability matter most.
- Limestone and granite are the two parent rocks most often quarried for gravel, and both hold up well under normal weathering, though granite tends to resist wear slightly longer under heavy vehicle traffic.
Pro Tip: If you are unsure whether a stone is washed or unwashed, rub a handful between your fingers. A dusty residue means fines are present, which is fine for a base layer but worth avoiding on a decorative or drainage top layer.
Which gravel size fits your project
Matching size to job comes down to three questions: will the surface carry weight, does water need to move through it, and does appearance matter more than performance. The rules below cover the projects that come up most often.
- Driveways need a layered build rather than one size throughout: a coarse sub-base (around 40 to 63 millimetres), a compacted crusher run binder layer, and a top dressing of #8 gravel or pea gravel for the visible surface.
- Paths and patios carry less weight than a driveway, so a single compacted layer of 10 to 20 millimetre angular stone over a thin base usually gives a stable, comfortable surface underfoot.
- French drains and drainage trenches work best with 10 to 20 millimetre clean, angular stone with no fines, since the goal is fast water movement rather than compaction, and rounded pebbles offer little advantage here.
- Decorative borders and flower beds suit pea gravel in the 3 to 8 millimetre range, which sits neatly around plants without smothering roots and reads as tidy from a distance.
- Play areas and informal seating zones benefit from rounded pea gravel at the finer end of its range, since sharp angular edges are uncomfortable for bare feet and small hands.
Our guide to choosing the right gravel for driveways, paths and gardens walks through these matches with more worked examples if you are planning more than one area at once.
Getting the layers and depths right
A driveway that fails within a year almost always fails because the depths or the compaction were wrong, not because the wrong stone was chosen. A typical durable build uses three layers: a compacted sub-base of 100 to 150 millimetres of coarse angular stone (often #3 grade), a binder layer of 75 to 100 millimetres of crusher run, and a top dressing of 25 to 50 millimetres of #8 gravel or pea gravel. Our driveway depth guide sets out the compaction method step by step for anyone building from scratch.
- Compact each layer separately with a plate compactor rather than relying on vehicle traffic to settle the stone over time.
- Install edging along the perimeter before adding the top layer, since loose gravel without a boundary migrates onto lawns and paths within weeks.
- On a sloped driveway, use angular rather than rounded stone in the top layer, as rounded gravel washes downhill far more readily in heavy rain.
Pro Tip: Garden paths and planter beds need far shallower depths than a driveway, usually 30 to 50 millimetres of gravel over a permeable membrane, since they carry no vehicle load and only occasional foot traffic.
For anyone ordering washed stone specifically for a driveway surface, our page on ordering washed driveway gravel covers the specification details suppliers need before dispatch.

What to check before and after your gravel arrives
Getting the right stone on site starts with asking the right questions before you order, not after a lorry has already tipped the wrong material onto your drive. A few minutes of checking at each end of the delivery saves a return trip and a second invoice.
- Confirm the exact millimetre range in writing, since a name like “20 mm gravel” can vary between suppliers even when the label matches.
- Ask whether the stone is washed or unwashed, and how much fine material it contains, particularly for drainage or top-layer use.
- Check the parent rock type, since limestone and granite weather differently and some regions restrict certain rock types for specific uses.
- Agree the tipping location with the delivery driver in advance, especially on a shared driveway or a site with limited vehicle access.
- On delivery, spread a small sample across a flat surface and photograph it against a tape measure if the size or colour looks wrong, since this is the evidence a supplier needs to process a correction quickly.
Our gravel coverage calculator guide helps convert a planned area and depth into the tonnage to order, which avoids both under-ordering and paying for stone you will not use.
Getting the balance between looks and durability right

The biggest mistake in gravel selection is picking purely on appearance and assuming any stone will hold up under daily use. Rounded pea gravel looks softer and more natural, but it needs regular raking and periodic topping up wherever feet or tyres push it out of place, as detailed in driveway oil stain removal: what to try first for proper maintenance. Angular crushed stone looks more utilitarian but holds its shape and position for years with minimal upkeep, which is why it belongs under any surface that carries real weight.
The sensible compromise, in most driveway projects, is to let performance dictate the base and binder layers and let appearance dictate only the thin top dressing. A layered driveway using coarse stone below and a decorative top layer above gives you both the durability and the look, and it remains the most reliable approach for a surface expected to last.
— Constantin
How Power Aggregates can help you get the right size
Once you know the millimetre range your project needs, the next step is finding a supplier who can confirm it before the lorry leaves the yard. There are suppliers who provide decorative stone, drainage stone and crusher run in clearly stated metric sizes, with nationwide delivery and advice on the right size for specific projects.

- Browse the full decorative stone range for pea gravel, pebbles and top-layer options in the sizes covered above.
- Check drainage stone options for French drains and water-management projects needing clean 10 to 20 millimetre stone.
- Request a sample bag before ordering in bulk, and use the coverage guidance on our site to confirm tonnage before you commit.
Visit the shop to see current stock and get advice tailored to your project before you order.
Sources
FAQ
What are the different sizes of gravel?
Gravel is generally grouped into fine (2 to 6.3 millimetres), medium (6.3 to 20 millimetres) and coarse (20 to 63 millimetres) under ISO 14688. Within those bands, suppliers sell named products such as pea gravel, #8 and #57, each tied to a specific sieve range for a particular job.
Should I use 10mm or 20mm gravel for my driveway?
Most driveways use both: a coarser 20 millimetre stone in the base and binder layers for stability, and a finer 10 millimetre or pea gravel top layer for appearance and comfort underfoot. Using only 10 millimetre stone throughout tends to shift and rut under vehicle weight without a firmer layer beneath it.
How much does 1 tonne of 20mm gravel cover?
Coverage depends on the depth you spread it to, since a compacted cubic metre of gravel weighs around 1,800 kilograms according to industry bulk density references. Our coverage calculator guide converts your planned area and depth into the tonnage you need to order.
What does #5 gravel look like?
Definitions for numbered gravel sizes vary between regional gradation tables, so “#5” is not a universally fixed size and is worth confirming directly against the millimetre range a specific supplier quotes. A safer approach is to ask for the stated mm range rather than relying on the number alone, as covered earlier in this guide.
What is the difference between crusher run and pea gravel?
Crusher run is a graded mix of crushed angular stone from roughly 0 to 40 millimetres, including fines, and is used as a compacted binder layer beneath paving and driveways. Pea gravel is a rounded, fines-free decorative stone around 3 to 8 millimetres, used for borders, paths and visible surfaces rather than structural layers.
