For most raised beds and garden edging, a 2.4m sleeper measuring roughly 200mm by 100mm is the practical standard. Reclaimed hardwood sleepers run closer to 2.6m by 250mm by 125mm and suit heavier retaining work, while shorter 1.2 to 1.8m lengths fit tight access and longer 3.0 to 3.6m sleepers cover large runs. Treat every measurement as approximate: timber varies, so allow room for trimming.
TL;DR:
- A 200×100mm sleeper gives most raised beds workable depth; stack two courses for deeper soil, while a shallower 200×75mm section suits edging.
- Use 250×125mm reclaimed hardwood for retaining walls, and choose hardwood or engineered sleepers for driveways because standard softwood cannot handle repeated vehicle loads.
- Nominal sizes can vary by roughly 5 to 25 millimeters, so measure actual stock, allow trimming room, and treat freshly cut ends with preservative.
- For stacked or retaining structures, use bolts every 400 to 600 millimeters, stagger course joints, and backfill walls with free draining material.
Table of Contents
- Common sleeper sizes and what the numbers mean
- Which size suits which garden project: a quick selection guide
- Materials and variability: softwood, reclaimed hardwood and treatments
- Measuring, ordering and delivery considerations
- Basic fixing and installation tips for sleepers
- Supplier guidance on sizes, delivery and safety
- Practical perspective: pick the size you can move and maintain
- Order sleepers and related materials from Power Aggregates
- FAQ
- Sources
Common sleeper sizes and what the numbers mean
Sleepers are sold in a handful of standard lengths, and knowing them before you measure a project saves wasted cuts. The most common nominal lengths are:
- 1.2m: ideal for small raised beds, planters and tight corners.
- 1.8m: a middle ground for short borders and compact steps.
- 2.4m: the most widely stocked length, used for raised beds, edging and general landscaping.
- 2.6m: typical of reclaimed stock, often used for retaining walls and heavier structural work.
- 3.0m to 3.6m: longer runs for boundary walls or large retaining projects, usually requiring two people or more to handle.
Cross-sections follow a similar pattern, with 200×100mm as the everyday size, 250×125mm for reclaimed or heavy-duty hardwood, and 200×75mm where a lighter, shallower edge is enough. These figures are nominal rather than exact. New planed softwood sleepers are commonly sold at around 2.4m with finished dimensions closer to 2400×195×95mm once planing has taken its toll, and weigh roughly 30 to 40 kilograms. Reclaimed sleepers commonly approximate 2.6m by 250mm by 125mm, but expect knots, splits and waney edges that affect finish without affecting strength.
Reclaimed sleepers typically weigh more than new softwood equivalents, which matters when you’re planning how many people you need on site to move them.

Which size suits which garden project: a quick selection guide
Matching the sleeper to the job stops you overbuying or underbuilding. A quick way to think about it:
- Raised beds: a single 200×100mm sleeper gives a workable depth for most vegetables; stack two courses for deeper beds or where soil volume needs to be greater.
- Edging and low borders: shorter lengths with a shallower 200×75mm cross-section keep the look neat without unnecessary bulk or cost.
- Steps and retaining walls: choose the heavier 250×125mm reclaimed or hardwood option, since a single softwood sleeper rarely has the strength to hold back loaded soil on its own; our sleeper steps design guide covers riser dimensions in more detail.
- Driveways and vehicular areas: hardwood sleepers or engineered alternatives handle repeated loading better than standard softwood, which isn’t built for that kind of pressure.
Working through the list in order, from light garden features to load-bearing structures, makes the sizing decision far less of a guessing game.
Materials and variability: softwood, reclaimed hardwood and treatments
New planed softwood sleepers are consistent and lighter, which makes them easier to handle and predict when you’re designing to a tight layout. Reclaimed hardwood sleepers tell a different story: dimensions can vary by several centimetres from one sleeper to the next, since each one has already lived a working life before reaching a garden.
- Planing reduces nominal dimensions, so a sleeper sold as 200×100mm often finishes a little smaller once planed.
- Reclaimed stock is prized for strength and character but is less dimensionally predictable than new PAR sleepers.
- Older sleepers may carry creosote from their original use, which is unsuitable for vegetable beds; modern preservative treatments are formulated to be safer for soil contact, and our guide to raised beds and sleeper treatment explains the distinction.
Pro Tip: Always treat freshly cut ends with a suitable preservative before installation, since factory treatment rarely penetrates a new cut face.
Measuring, ordering and delivery considerations
Measure the full run of your bed, wall or border first, then work out how many sleepers you need with as few cuts as possible. Cutting wastes material and weakens the factory-treated surface at the cut point.
- Add a small allowance for trimming and for the shrinkage that happens as green timber seasons over time.
- Plan layouts around standard lengths (1.2m, 1.8m, 2.4m) rather than designing to odd measurements that force extra cuts.
- Expect genuine variance: mills typically work to a tolerance of roughly 5 to 25 millimetres either side of the nominal size.
Delivery cost is often driven more by the space sleepers take up on a lorry than by weight alone, so shorter sleepers can be cheaper to deliver than long 3.0 to 3.6m lengths. For budgeting a wider project, Workily’s guide to landscaping costs is a useful starting point before you place an order.
Basic fixing and installation tips for sleepers
Getting sleepers to sit square and stay put comes down to the right fixings and a bit of planning before you start.
- Use timber screws or dedicated sleeper bolts for stacked beds, spacing them roughly every 400 to 600mm along the length.
- For retaining structures, add dowels or longer bolts driven through multiple courses to stop lateral movement under soil pressure.
- Stagger joints between courses, the way you would with brickwork, so no single vertical line runs through the whole structure.
- Backfill retaining walls with free-draining material behind the sleepers to relieve water pressure rather than letting it build up against the timber.
Pro Tip: Leave fixings slightly adjustable where possible, since seasoning can shift timber by a few millimetres and you may need to realign a course months later. For step-specific riser heights, our sleeper steps design page sets out practical limits.
Supplier guidance on sizes, delivery and safety
We stock a working range of sleeper sizes and treatments, and our railway sleepers category lists current lengths and cross-sections so you can check what’s available before you measure a final layout.
- Delivery estimates may vary based on sleeper length and quantity, since longer lengths take up more lorry space and generally cost more to move.
- Advice on handling heavier reclaimed sleepers is recommended, including when additional help may be needed.
- Treatment details and guidance on treating cut ends after trimming on site can be obtained from suppliers.
- Our sleeper lifespan notes cover service life and suitability checks worth reading before you commit to a material.
Practical perspective: pick the size you can move and maintain
The sleeper that looks best in a photo isn’t always the one you can lift, cut and fit on a Saturday afternoon. Favour lengths your access and helpers can actually manage, and design to standard sizes wherever you can. Every cut you avoid is money and effort saved.
— Constantin
Order sleepers and related materials from Power Aggregates
We make it straightforward to find the right sleeper size for your project without guessing at dimensions from a catalogue photo. Our shop lists sleepers alongside the decorative stone, drainage material and paving you might need for the same job, so you can plan a full garden project in one order.

- Nationwide delivery is often available with cost estimates depending on sleeper length and order size.
- Practical advice on handling and treatment is often provided before committing to a quantity.
- Guidance on cut-end treatment needs can help ensure sleepers last as intended.
Browse our railway sleepers range or get in touch for a delivery estimate on your project.
FAQ
How do you fit railway sleepers together?
Sleepers are typically joined with timber screws or dedicated sleeper bolts, spaced at regular intervals along stacked courses. For retaining walls, longer bolts or dowels driven through multiple courses add the lateral strength needed to resist soil pressure.
What is the standard height of a sleeper?
Sleeper height, or depth, usually runs around 100mm for new softwood and up to about 125mm for reclaimed hardwood. Stacking two or more courses is the common way to reach greater heights for raised beds or low walls.
What is the length of a concrete sleeper?
Concrete sleepers follow tighter engineering tolerances under EN 13230, a standard built for rail infrastructure rather than garden use. For garden projects, timber sleeper dimensions and supplier tolerances are the more relevant reference point.
Where can you find railway sleepers for sale?
Garden centres and specialist timber suppliers stock both new and reclaimed sleepers in standard lengths. Our railway sleepers category lists current sizes and treatments if you want to check availability before ordering.
Do reclaimed and new sleepers come in the same sizes?
Not exactly. New planed sleepers are sold to fairly consistent sizes, while reclaimed sleepers vary more from one piece to the next, so it’s worth checking actual dimensions rather than assuming they match nominal figures.
Sources
- Railwaysleepers
- Railway sleeper dimensions UK — Cranerailclips
- DIN EN 13230-1:2016 — concrete sleepers standard
