Type 804, officially “Clause 804” unbound granular material (UGM), is a crushed rock sub-base used under driveways, patios and roads across Ireland. It comes from quarry stone, graded to a specific particle mix, and packs down into a stable foundation layer. If you plan to lay it under a building or floor slab, insist on SR21-certified material. For everything else, follow the buying and installation checks below.
TL;DR:
- Proper certification, specifically SR21, is essential for any 804 used under buildings or internal slabs to prevent pyrite-related floor heaving and cracking.
- Always request a batch-specific grading sheet and certificate from the quarry source to ensure the material meets TII standards for road or groundworks projects.
- Layer the sub-base in lifts of about 100 to 150mm, properly compacted with appropriate equipment, and ensure moisture levels are within the optimal range for best performance.
- When ordering, confirm the source quarry, delivery logistics, and documentation beforehand to avoid mixing substandard or uncertified material into your project.
- Use 804 primarily for driveways, patios, and landscaping, but avoid using it as a substitute in concrete mixes, as it is designed solely for load-bearing sub-base applications.
Table of Contents
- What is type 804 stone? Composition and how quarries label it
- Standards and certification: TII, IS EN 13242 and SR21 explained
- Where can you use type 804 in Ireland?
- How do you choose and order the right 804?
- Installation best practice: layers, compaction and coverage
- MOT type 1 vs 804: clearing up the biggest confusions
- Power Aggregates: local sourcing, delivery and how we support Irish projects
- Authoritative standards and supplier pages to consult
- What DIYers actually get wrong about type 804
- Get your 804 sub-base material sorted with Power Aggregates
- Sources
- FAQ
What is type 804 stone? Composition and how quarries label it
Clause 804 is unbound granular material, meaning it’s crushed rock that hasn’t been mixed with cement or bitumen. It relies purely on particle interlock and compaction for strength. That single fact explains almost everything else about how it behaves: get the grading and moisture right, and it locks together into a dense, load-bearing layer; get either wrong, and it stays loose and prone to rutting.
The stone itself is quarried rock, typically limestone in most of Ireland, crushed and screened into a controlled range of particle sizes. You’ll see it called several things depending on who’s selling it: Clause 804, UGM, UGM A, or UGM Ac. These aren’t different products so much as different labels for the same specification family, with the letter suffix pointing to which grading envelope the batch falls within. Irish suppliers commonly market it under the UGM label, listing driveways, patios and paving foundations as typical end uses.
A proper grading sheet (sometimes called a particle size distribution or PSD) shows the percentage of material passing through a series of sieve sizes, from around 40mm down to dust. What you’re looking for is a well-graded mix, meaning it contains a spread of particle sizes rather than being dominated by one size. That spread is what allows smaller particles to fill the gaps between larger ones during compaction, squeezing out air and water and creating density.
When a supplier hands you a datasheet, here’s what actually matters on it:
- Maximum particle size, usually 40mm for standard 804, which determines how coarse the finished surface will feel underfoot before a wearing course is added.
- Fines content (material passing the 0.063mm sieve), since too much fines makes the layer hold water and lose strength when wet.
- Grading envelope reference, ideally cross-checked against the TII specification rather than taken on trust.
- Source quarry, because consistency between loads matters more than most buyers realise.
If a supplier can’t produce a grading sheet on request following material testing standards, that’s worth treating as a red flag rather than a formality.
Standards and certification: TII, IS EN 13242 and SR21 explained
Three sets of letters govern almost every conversation about 804 in Ireland, and confusing them is where most buying mistakes start.
TII (Transport Infrastructure Ireland) publishes the specification most contractors actually build to. Its Road Pavements: Unbound Materials document, part of the CC-SPW-00800 series, defines 804 as a crushed rock unbound granular material and sets out the performance criteria, grading envelopes and moisture ranges it must meet for use in roadworks. This is the reference document engineers and quarries use when they say material “meets 804 spec.”
IS EN 13242 is the European standard for aggregates used in unbound and hydraulically bound materials in civil engineering and road construction. It sets baseline requirements for durability, particle shape and resistance to fragmentation. Most quarried aggregate sold in Ireland carries CE marking against this standard, but conformity to IS EN 13242 alone doesn’t tell you whether a specific batch is safe to use under a building.
That’s where SR21 comes in. SR21 is the Irish testing standard developed largely in response to pyrite contamination cases that damaged thousands of homes over the past two decades. It goes beyond the general aggregate standard to test specifically for pyrite content and chemical stability, the properties that matter when stone will sit beneath a concrete floor slab in a damp, enclosed void. Industry technical guidance is blunt about the distinction: material used under buildings needs SR21 certification because that testing goes well beyond what road-grade 804 requires.
The practical problem is that “804” sold under the same name from different sources can vary hugely in quality, and buyer discussions frequently flag that not everything marketed as 804 online has been through SR21 testing at all.
Before you accept a delivery for use under a house extension, garage floor or any internal slab, ask for:
- A current SR21 test certificate specific to the batch or quarry source, not a generic brochure claim.
- The NSAI paperwork or laboratory reference number backing that certificate.
- A grading sheet showing the material sits within the TII 804 envelope.
- Written confirmation of the source quarry, since certification is tied to a specific pit, not a generic product name.
Pro Tip: Keep a photo of the delivery ticket and a sample bag from every load used under a building. If a floor ever develops heave or cracking years later, that paperwork is the difference between a straightforward insurance claim and a drawn-out dispute over what was actually used.
Where can you use type 804 in Ireland?
Type 804’s versatility is exactly why it’s the default sub-base choice for most Irish ground-up projects, but “versatile” doesn’t mean “universal.” Matching the material to the job still matters.
Driveways are the classic 804 application. For a domestic driveway carrying car traffic, a typical compacted depth is within a moderate range, laid over a proof-rolled and, where the ground is soft or clay-heavy, geotextile-separated subgrade. Heavier vehicle traffic or poor underlying ground calls for a thicker layer, often applied in multiple compacted lifts. The angular, crushed nature of 804 particles is what gives it an edge over rounded gravels here: angular stone locks together under compaction in a way rounded pea gravel simply can’t, which is why 804 outperforms decorative gravel as a structural base even though both are sold as “aggregate.”
Patios and paved areas generally need less depth than a driveway, typically 100 to 150mm of compacted 804 beneath a sand or mortar bedding layer, depending on the paving type. For lightweight decorative paving on well-drained ground, a shallower sub-base can work, but skipping it entirely to save money is the single most common reason patios sink and slabs rock within a year or two of laying.
Road construction and larger landscaping projects follow TII guidance more formally, with layer thickness, compaction standards and testing frequency specified by the engineer on the job. If you’re doing groundworks for a shared driveway, access road or larger commercial landscaping scheme, that’s the document your contractor should be referencing.
Drainage is where 804 needs a supporting cast. On its own, a well-compacted 804 layer sheds surface water reasonably well because of its granular structure, but it isn’t designed as a primary drainage medium. Combine it with a free-draining layer, perimeter drains, or a permeable membrane where standing water is a known issue, and always fall the finished surface away from buildings. Using 804 as a substitute for proper land drainage in genuinely wet ground is asking for trouble.
If you’re still deciding on depth for your specific project, our guide to sub-base thickness for patios and drives breaks it down by surface type.
How do you choose and order the right 804?
Getting the paperwork and the load right at the ordering stage saves far more hassle than trying to fix a bad delivery after it’s dumped on your drive. Work through these questions before you commit to an order:
- Is this material SR21-certified, and can you send the certificate before delivery? If the answer is vague or the certificate is generic rather than batch-specific, treat that as a warning sign, especially for any under-building use.
- Can you provide a current grading sheet? A supplier confident in their product will have this ready without being asked twice.
- What quarry does this come from, and is that quarry named on the certification? Certification tied to “our stone” without a named source is close to worthless.
- How is the load being delivered, and what access do you need? Ex-pit collection, bulk tipper delivery, and bagged retail supply all come with different logistics, and a tipper needs a genuinely clear run to your tipping point, not just a driveway that looks wide enough on a good day.
- What happens if the load looks wrong on arrival? Ask this before the truck arrives, not after.
On cost and logistics, buying direct from a quarry rather than a builders’ merchant or bagged retail line tends to work out more efficient for larger jobs, since you’re cutting out a handling step and often get better access to grading documentation straight from the source. Ringing a local quarry directly and asking about ex-pit collection or bulk delivery is worth doing even if you end up ordering through a supplier in the end, purely for the pricing comparison.
Pro Tip: When the delivery arrives, grab a handful from three different points in the load, not just the top. Uneven mixing during loading is common, and a quick visual check for consistent particle size across the pile tells you more than any certificate about whether you got what you paid for.

Keep every piece of paperwork, the delivery docket, the certificate, and any photos, in one folder for the project. If a dispute ever arises about what material went where, that folder is your evidence.
Installation best practice: layers, compaction and coverage
A sub-base is only as good as the ground beneath it and the compaction effort put into it. Rushing this stage is the single biggest reason otherwise correctly specified 804 fails to perform.

Start with proper site preparation. Strip out topsoil, roots, and any organic matter down to firm subgrade, because organic material decomposes over time and creates voids that the surface above will eventually settle into. Once you’re down to bare ground, proof-roll it: run a loaded wheelbarrow, plate compactor, or even just walk it heavily to spot soft patches that flex or pump water to the surface. Any soft spot found now is a problem solved cheaply; found after paving is laid, it’s a problem solved expensively. On clay or consistently wet ground, lay a geotextile membrane before the first stone goes down. It stops the sub-base migrating into the subgrade and the subgrade pumping up into the stone, a slow-motion failure that otherwise ruins a sub-base from underneath over a few wet winters.
Build the layer in lifts, not one big dump. Industry practice for unbound granular sub-bases is to place material in lifts of roughly 100 to 150mm loose depth, compacting each one before adding the next. Tipping the full depth in one go and compacting only the top might look fine on the day, but the lower material stays loose, and loose material under a driveway shows up as rutting and pooling within a year. For a domestic driveway, that typically means two lifts to reach a 200 to 250mm compacted total depth.
Match your compaction equipment to the job. A vibrating plate compactor (wacker plate) suits patios, paths and smaller driveway areas. For larger drives or any road-scale work, a vibrating roller does the job faster and more evenly. As a rough guide:
- Spread the first lift evenly across the prepared area, raking out any obvious high or low points.
- Compact with several passes of the plate or roller until the surface stops visibly deforming underfoot.
- Spread and compact the second lift the same way, checking overall depth as you go.
- Finish with a final pass across the whole area to bed the surface uniformly before any wearing course or bedding sand goes on top.
Moisture control matters more than most DIYers expect. 804 compacts best within a fairly narrow moisture window, damp enough that fines bind particles together, dry enough that water isn’t lubricating them apart. Bone dry material simply won’t lock up under compaction; sodden material squelches and won’t densify either. A rough field check: squeeze a handful, and if it holds together loosely without dripping water, you’re close to the right range. If it’s raining heavily on install day, it’s usually worth waiting rather than compacting a saturated layer.
Working out how much to order comes down to a simple density conversion. Crushed rock aggregates like 804 typically weigh in the region of 1.6 to 1.8 tonnes per cubic metre when compacted, so for a 200mm compacted depth, roughly 0.32 to 0.36 tonnes covers each square metre. A 50m² driveway at that depth needs somewhere around 16 to 18 tonnes, before accounting for compaction losses, which is why most suppliers recommend ordering a little over the theoretical minimum. For an exact figure tailored to your depth and area, our gravel coverage per tonne planning guide and the dedicated 804 sub-base guide both walk through the maths for different depths.
MOT type 1 vs 804: clearing up the biggest confusions
Three questions come up more than any others when people research 804, and getting them wrong is expensive.
Is MOT Type 1 the same as 804? No, though they’re often used for similar jobs and get confused constantly. MOT Type 1 is a British specification (from the Department of Transport’s old Specification for Highway Works), while Clause 804 is the equivalent Irish designation referenced in TII documents. Both are crushed, well-graded unbound granular materials for sub-base use, and in practice their grading envelopes overlap closely enough that many Irish suppliers will describe stock as “MOT Type 1 / 804” interchangeably. The key point isn’t which name is on the bag, it’s whether the actual grading and certification match what your project needs.
Can you use 804 to make concrete? Not as a direct substitute for proper concrete aggregate, no. Concrete needs graded coarse and fine aggregate that meets its own specific standard for strength, durability and chemical purity, quite different requirements from an unbound sub-base material. 804’s grading is designed for compaction and load spreading, not for the particle shape and cleanliness concrete mixes demand. Using 804 in a concrete mix risks weak, porous concrete that fails structurally, so always source dedicated concrete aggregate for that job.
Why does pyrite matter, and when do you actually need SR21? Pyrite is an iron sulphide mineral that, when present in fill material beneath a floor slab and exposed to moisture and oxygen, expands and causes the floor above to heave and crack, sometimes badly enough to require full replacement. It’s why SR21 testing exists at all: to catch pyrite-bearing stone before it goes under a house. Rule of thumb: anything going under a building, floor slab or in an internal void needs SR21-certified material; anything staying outdoors as a driveway or patio sub-base, exposed to weather and not enclosed against a structure, generally doesn’t carry the same risk profile. If you’re ever unsure which category your job falls into, that’s worth a call to a structural engineer rather than a guess.
Power Aggregates: local sourcing, delivery and how we support Irish projects
Clause 804 and other sub-base materials are commonly sourced from quarries in Cork, with delivery services available nationwide to homeowners, builders and contractors across Ireland. Sourcing directly from the pit means you’re not paying for extra handling layers between quarry and driveway, and it means we can speak to exactly where your stone came from rather than pointing to a generic supply chain.
When customers ask about SR21 certification, we talk through what the job actually needs before recommending a product. A patio sub-base and a floor slab sub-base are different jobs with different certification requirements, and matching the material to the use is more useful than defaulting everyone to the most expensive option.
Practical things we help with on a typical enquiry:
- Confirming whether your project needs SR21-certified stone or standard road-grade 804.
- Talking through grading sheets and what they actually mean for your specific depth and compaction plan.
- Advising on bulk delivery logistics, including tipping access and quantity estimates for driveways, patios and larger groundworks.
- Pointing you towards the right complementary material, drainage stone, bedding sand, or decorative finishes, once the structural layer is sorted.
If you’re planning a project and want a second opinion on quantities or certification before you order, get in touch with our team directly rather than guessing from a general online estimate.
Authoritative standards and supplier pages to consult
For the technical detail behind everything covered here, the primary reference is TII’s Road Pavements: Unbound Materials specification, which sets the grading and performance rules that “804” actually means in practice. IS EN 13242 governs the general European aggregate standard, while SR21 covers the additional testing needed for material used under buildings, explained in more detail on IrishConcrete’s technical guidance page.
For the practical side of buying and calculating quantities, our own guides cover choosing hardcore for driveway sub-bases and working out gravel coverage per tonne for different project depths and areas.
What DIYers actually get wrong about type 804
The conventional advice on 804 treats it as a commodity, ask for “804,” get a delivery, job done. That framing is where most problems start. The material itself is genuinely simple: crushed rock, well graded, compacted in lifts. What separates a good sub-base from a failed one is almost never the stone. It’s whether anyone checked the paperwork.
If there’s one thing worth prioritising above depth calculations, compaction technique, or even price, it’s asking the certification question before the truck arrives, not after the concrete’s poured on top. SR21 testing exists specifically because “804” from two different sources can be meaningfully different products wearing the same name, and the boards.ie discussions on this topic show just how often buyers only discover that gap after something’s gone wrong.
The overrated variable is brand or supplier reputation alone. The underrated one is a named quarry source and a batch-specific certificate you can actually produce years later if a floor starts to heave. Get that right first, and the depth and compaction advice in this guide will do the rest.
— Constantin
Get your 804 sub-base material sorted with Power Aggregates
Clause 804 sub-base material is available from suppliers sourcing directly from Cork quarries, with nationwide delivery options, allowing customers to purchase closer to the source than through intermediaries. That matters most on the exact question this guide has spent most of its length on: certification. Where a builders’ merchant might sell you “804” without knowing which pit it came from, we can tell you precisely, and confirm whether SR21 testing applies to your batch before it leaves the yard.

Whether you’re prepping a driveway, patio, or a larger groundworks job, our team will talk through your depth, tonnage and certification needs before you order, not after. Browse the full aggregates and building materials range online, or check the decorative stone and gravel selection if you’re also finishing off the visible parts of the project. Get in touch with a quantity estimate for your area and depth, and we’ll confirm exactly what grade and certification suits the job before anything gets delivered.
Sources
FAQ
What is Clause 804 called now?
Clause 804 is still commonly called by that name in Ireland, alongside “Type 804” and “UGM” (unbound granular material), which is how most quarries and suppliers label it on datasheets and invoices.
What is 804 used for?
Type 804 is used mainly as a sub-base under driveways, patios, roads and general hard landscaping, providing a compacted, load-bearing layer beneath the finished surface.
Is MOT Type 1 the same as 804?
Not officially. MOT Type 1 is a British specification and Clause 804 is its Irish equivalent, but both are similarly graded crushed unbound granular materials used for the same sub-base purpose, so suppliers often treat them as interchangeable in practice.
Can you use 804 to make concrete?
No. Type 804 is graded for compaction as a sub-base, not for the particle cleanliness and shape required in concrete mixes, so it should not replace dedicated concrete aggregate.
When do you need SR21-certified 804 instead of standard 804?
SR21 certification is needed whenever the material will be used under a building, floor slab, or any enclosed internal space, because SR21 testing checks specifically for pyrite content and chemical stability that standard road-grade 804 testing does not cover.